Keller LEO 3 Digital Manometer

Quick Overview

Keller Digital Manometer LEO 3 ACCURACY 0,1% LEO 3 combined digital manometer / display and pressure transmitter available for pressure ranges up to 1000 bar with 4-20mA output.

View Options

Details

Intelligent Transmitter with Digital Indication

LEO 3 is a micro-processor based transmitter with digital double-display for pressure (top display) and for the output signal (bottom display). The display is powered from the 4...20 mA current loop.

The following functions can be executed with the front keys:

MAX/MIN:
Activating the right key brings the Max.- and Min.-values to the lower display. After 5 seconds, the analog signal is indicated again.

RESET:
With RESET, the Max.- and Min.-values are set to actual.

ZERO SET:
The zero is set to the applied pressure.

ZERO RES:
Restores the instrument back to factory settings.

UNITS:
The pressure values can be displayed in the following units:
bar, mbar/ hPa, kPa, MPa, PSI, kp/cm2.

Programming the Analog Output via the front Keys:

OUTP SETT:
This sub-menu is used to configure the analog output within the compensated range.

ZERO:
Executing ZERO when pressure is applied sets the analog output to 4 mA.

FS:
Executing FS when pressure is applied sets the analog output to 20 mA.

FACT SETT:
The analog output is set back to factory settings.

Programming by PC:

The communication with the BUS-capable instrument takes place with the KELLER PROG30/ READ30 software and the K106 converter via the RS 485 interface, allowing to read out the pressure values and the instrument characteristics. The analog output can be programmed without applying pressure to the instrument.

Specification
Pressure Ranges	0...4 bar abs. 0...30 bar abs. 0...300 bar 0...700 bar 0...1000 bar
Accuracy	0,1% FS typ.
Storage Temperature	-10...60 °C
Compensated Temperature Range	0...50 °C
Protection	IP65

Availability: Stock Item

Components / Downloads

For further information, technical advice, or a quotation please call or email us. If you are not sure which product you need one of our technical sales advisors will be happy to discuss your application. We also accept company purchase orders by fax or post. Credit card orders can also be placed over the phone for any product.

REF	DESCRIPTION	DOWNLOADS	PRICE	ORDER ITEM

Keller LEO 3 Digital Manometer
LEO3-4	LEO3 Digital Manometer with programmable 4-20mA output and RS485 communications. The LEO 3 displays both the current pressure reading and the output signal value. Pressure range 0 to 4 BarA, accuracy of 0.1%. Pressure connection 1/4 inch BSP male connection, operating temperature 0 to 50 C and IP65 casing. Manometer is loop powered with a 8-28vDC power supply range on the 2 wire 4-20mA output. Units are supplied with a 5 pin Binder mating connector.	Datasheet Size: (463.07 KB)	£450.00	or call us for a quote
LEO3-30	LEO3 Digital Manometer with programmable 4-20mA output and RS485 communications. The LEO 3 displays both the current pressure reading and the output signal value. Pressure range 0 to 30 BarA, accuracy of 0.1%. Pressure connection 1/4 inch BSP male connection, operating temperature 0 to 50 C and IP65 casing. Manometer is loop powered with a 8-28vDC power supply range on the 2 wire 4-20mA output. Units are supplied with a 5 pin Binder mating connector.		£450.00	or call us for a quote
LEO3-300	LEO3 Digital Manometer with programmable 4-20mA output and RS485 communications. The LEO 3 displays both the current pressure reading and the output signal value. Pressure range 0 to 300 BarG, accuracy of 0.1%. Pressure connection 1/4 inch BSP male connection, operating temperature 0 to 50 C and IP65 casing. Manometer is loop powered with a 8-28vDC power supply range on the 2 wire 4-20mA output. Units are supplied with a 5 pin Binder mating connector.		£450.00	or call us for a quote
LEO3-700	LEO3 Digital Manometer with programmable 4-20mA output and RS485 communications. The LEO 3 displays both the current pressure reading and the output signal value. Pressure range 0 to 700 BarG, accuracy of 0.1%. Pressure connection 1/4 inch BSP male connection, operating temperature 0 to 50 C and IP65 casing. Manometer is loop powered with a 8-28vDC power supply range on the 2 wire 4-20mA output. Units are supplied with a 5 pin Binder mating connector.		£550.00	or call us for a quote
LEO3-1000	LEO3 Digital Manometer with programmable 4-20mA output and RS485 communications. The LEO 3 displays both the current pressure reading and the output signal value. Pressure range 0 to 1,000 BarG, accuracy of 0.1%. Pressure connection 1/4 inch BSP male connection, operating temperature 0 to 50 C and IP65 casing. Manometer is loop powered with a 8-28vDC power supply range on the 2 wire 4-20mA output. Units are supplied with a 5 pin Binder mating connector.		£550.00	or call us for a quote

Keller Software & Programming Kit
K104B	K114B Programming software and Binder connection cable. Suitable for programming (Series 33-39, Series 53-55 and LEO 3 pressure sensors). 1.8m cable length to a USB port for PC connection.		£160.00	or call us for a quote

Keller RS485 to USB Converter
K114	K114 RS485 to USB Converter with Screw Terminals. Connects to a PC via a USB (A) port and to the LEO 3 via screw terminals. Converter will provide a 10vDC power supply for a single LEO 3 and has a DC socket for an external supply to allow several devices to be connected to a PC via a single K-104 converter.		£150.00	or call us for a quote

LEO Gauge Accessories
LEO-CASE	Soft carry case for LEO digital manometers and loggers		£15.00	or call us for a quote
RUBCOV-LEO1/3	Protective Rubber cover for LEO1 & LEO3 digital manometers.		£14.00	or call us for a quote

Initial Calibrations
NPL-CAL-5 POINTS	Initial Calibration of pressure sensors purchased from Omni Instruments. Pressure Calibration to 5 points. All ranges between -0.8 and 1,000 Bar. Certificate shows actual output readings in graph and table form. Maximum errors shown at each point as a percentage. Certificate is timed, dated and has a unique reference for complete traceablility.		£37.50	or call us for a quote
NPL-CAL-11 POINTS	Initial Calibration of pressure sensors purchased from Omni Instruments. Pressure Calibration to 11 points. All ranges between -0.8 and 1,000 Bar. Certificate shows actual output readings in graph and table form. Maximum errors shown at each point as a percentage. Certificate is timed, dated and has a unique reference for complete traceablility.		£79.35	or call us for a quote