ComNav G3B GNSS Satellite with G2B Compass Differential GPS (DGPS) correction, G3 Colour Display and 15m cable. Output: NMEA0183. Update rate: Heading & position updates at up to 20 times per second, and can operate at sustained turn rates up to 90° per second. Power Supply 10 to 36vDC (250mA ...
GEN II radio transmitter for an external thermistor probe. Temperature Range -40 to +70°C, Resolution 0.1°C and Accuracy ±0.2°C (-15 to 40°C). Supplied with 4 x AA Alkaline batteries and stub antenna. ...
GS-DPA-AC Dual Port Adapter Input Module for AC current sensors. The GS-DPA-AC can measure electric power current by connecting an AC current sensor (50A clamp/GS-AC50A; 100A clamp/GS-AC100A; 200A clamp/GS-AC200A) single-phase 2 wire, single-phase 3 wire, three-phase 3 wire, to the GL100 Data Logger. Each adapter can be used with up ...
The POC module is meant as Pen Offset High current shunt for recorder ranges of 100mV or 200mV. Maximum continuous current is 16A. Peak current is 20A for 2 min. The shunt has no thermal or current protection and is tested for frequencies below 20 kHz. Fast mounting on all ...
This module transforms a 0-20 mA signal into a Voltage output by means of a highly accurate resistor (125 Ohm). Full accuracy is guaranteed over the recorder temperature range. ...
This module transforms a 4-20 mA signal into a Voltage output by means of a highly accurate resistor (125 Ohm). Full accuracy is guaranteed over the recorder temperature range. ...
ComNav G3B GNSS Satellite with G2B Compass Differential GPS (DGPS) correction, G3 Colour Display and 30m cable. Output: NMEA0183. Update rate: Heading & position updates at up to 20 times per second, and can operate at sustained turn rates up to 90° per second. Power Supply 10 to 36vDC (250mA ...
DACON8-UMB module will convert up to 8 UMB channels into current (0/4-20mA) or voltage (0/2 to 10V) outputs. Fully Configurable using UMB-Config-Tool ...
DARCA Software is used with the GEN II telemetry systems to help manage and analyse the data collected from the various different GEN II transmitters. DARCA Lite, DARCA Plus, DARCA Heritage and DARCA Secure. The table below shows a breakdown of the different versions and what each can provide. ...
Small data buoy, rotationally moulded polyethylene hull with integral ballast skirt. Diameter 0.7m. Buoyancy 50kg. Weight Approx.40kg. Including top frame with Marker Beacon (1NM, yellow -flashes 5 in every 20 secs), 2 x 14W Solar Panels. Sealed waterproof electronics canister containing 24Ah LiPo Battery Pack includes bulkheads for Solar input, ...
ADAQ data logger with CANBUS input suitable for LPMS CANBUS output, logs up to 8 LPMS IMU parameters such as euler angles, x,y,z, linear acceleration, gyro rates and heave motion. The logger also has 10 analogue inputs suitable for a wide range of sensors for load, pressure, temperature, displacement etc. ...
GEN II radio transmitter for one external thermistor inputs. Temperature probes, range -50 to +150°C, Resolution 0.2°C and Accuracy ±0.4°C (-40 to +125°C). Supplied with 4 x AA Alkaline batteries and stub antenna. ...
GS-AC50A Clamp-on AC Current Sensor. Range 0-50A RMS. Accuracy ±2%FS ±1 digit. Current clamp comes with 200mm cable for connection to the GS-DPA-AC module. ...
MiniAir20 Mini Steel vane anemometer. Air velocity range 0.8-40m/s with accuracy ±1.0% of full scale, ±2.0% of reading. Sensing head 22mm diameter x 28mm, probe length 182mm. Sensor is supplied with 1.8m cable and connector for interfacing with MC20 and MC 4.0 Displays with Lemo Connectors. Steel sensing head screwed ...
GS-AC100A Clamp-on AC Current Sensor. Range 0-100A RMS. Accuracy ±2%FS ±1 digit. Current clamp comes with 200mm cable for connection to the GS-DPA-AC module. ...
GS-AC200A Clamp-on AC Current Sensor. Range 0-200A RMS. Accuracy ±2%FS ±1 digit. Current clamp comes with 200mm cable for connection to the GS-DPA-AC module. ...
DC current sensor, range 100 amps, accuracy 1% of reading, response time 2ms from 10% to 90% of full scale. Operating temperature -40 to +80 C. Power supply 5vDC, Output 0.5-4.5vDC (0 amps = 2.5v). Accepts ring terminals for two 1/4-20 studs, supplied with 10ft cable. ...
DC current sensor, range 150 amps, accuracy 1% of reading, response time 2ms from 10% to 90% of full scale. Operating temperature -40 to +80 C. Power supply 5vDC, Output 0.5-4.5vDC (0 amps = 2.5v). Accepts ring terminals for two 1/4-20 studs, supplied with 10ft cable. ...
DC current sensor, range 200 amps, accuracy 1% of reading, response time 2ms from 10% to 90% of full scale. Operating temperature -40 to +80 C. Power supply 5vDC, Output 0.5-4.5vDC (0 amps = 2.5v). Accepts ring terminals for two 1/4-20 studs, supplied with 10ft cable. ...
Pyrheliometer Mounting Kit. To mount a CHP1/SHP1 series pyrheliometer to the side plate of the 2AP or Solys 2 Suntracker. ...
10130055
ComNav G3B GNSS Satellite with G2B Compass Differential GPS (DGPS) correction, G3 Colour Display and 15m cable. Output: NMEA0183. Update rate: Heading & position updates at up to 20 times per second, and can operate at sustained turn rates up to 90° per second. Power Supply 10 to 36vDC (250mA @ 12vDC). The G2B contains a ComNav receiver module (containing two GNSS receivers, a 3-axis gyro, a 3-axis accelerometer and a 3-axis magnetometer), a DGPS ...
8421
DIN Rail mounting clip for head mount transmitters ...
GC-04
GEN II radio transmitter for an external thermistor probe. Temperature Range -40 to +70°C, Resolution 0.1°C and Accuracy ±0.2°C (-15 to 40°C). Supplied with 4 x AA Alkaline batteries and stub antenna. ...
GS-DPA-AC
GS-DPA-AC Dual Port Adapter Input Module for AC current sensors. The GS-DPA-AC can measure electric power current by connecting an AC current sensor (50A clamp/GS-AC50A; 100A clamp/GS-AC100A; 200A clamp/GS-AC200A) single-phase 2 wire, single-phase 3 wire, three-phase 3 wire, to the GL100 Data Logger. Each adapter can be used with up to 2 AC current sensors simultaneously. The unit will also provide a calculated value for instantaneous power and electrical energy. 20 Byte record length, 89 ...
CURRENT SHUNT 0-16A
The POC module is meant as Pen Offset High current shunt for recorder ranges of 100mV or 200mV. Maximum continuous current is 16A. Peak current is 20A for 2 min. The shunt has no thermal or current protection and is tested for frequencies below 20 kHz. Fast mounting on all channels and includes safety banana connectors on both ends. ...
CURRENT SHUNT 0-20MA
This module transforms a 0-20 mA signal into a Voltage output by means of a highly accurate resistor (125 Ohm). Full accuracy is guaranteed over the recorder temperature range. ...
CURRENT SHUNT 4-20MA
This module transforms a 4-20 mA signal into a Voltage output by means of a highly accurate resistor (125 Ohm). Full accuracy is guaranteed over the recorder temperature range. ...
CUSTOMSCADA
Custom configuration of Superview SCADA Software to match application requirements for NOVUS devices. Price per hour for customisation. ...
10130056
ComNav G3B GNSS Satellite with G2B Compass Differential GPS (DGPS) correction, G3 Colour Display and 30m cable. Output: NMEA0183. Update rate: Heading & position updates at up to 20 times per second, and can operate at sustained turn rates up to 90° per second. Power Supply 10 to 36vDC (250mA @ 12vDC). The G2B contains a ComNav receiver module (containing two GNSS receivers, a 3-axis gyro, a 3-axis accelerometer and a 3-axis magnetometer), a DGPS ...
DA2597-SMART-CHARGER
Smart charger, 3A output for lithium polymer batteries. Charge time for 8AH batteries 4-6 hours, 22AH batteries 7-10 hours ...
DACON8-UMB
DACON8-UMB module will convert up to 8 UMB channels into current (0/4-20mA) or voltage (0/2 to 10V) outputs. Fully Configurable using UMB-Config-Tool ...
DARCA SOFTWARE
DARCA Software is used with the GEN II telemetry systems to help manage and analyse the data collected from the various different GEN II transmitters. DARCA Lite, DARCA Plus, DARCA Heritage and DARCA Secure. The table below shows a breakdown of the different versions and what each can provide. ...
Data Acquisition and Logging – Environmental Temperature Test Chamber
Monitoring of multiple temperature sensors in an environmental test facility for ATM cash dispenser units ...
DATABUOY-50KG
Small data buoy, rotationally moulded polyethylene hull with integral ballast skirt. Diameter 0.7m. Buoyancy 50kg. Weight Approx.40kg. Including top frame with Marker Beacon (1NM, yellow -flashes 5 in every 20 secs), 2 x 14W Solar Panels. Sealed waterproof electronics canister containing 24Ah LiPo Battery Pack includes bulkheads for Solar input, on/off, Antenna and 1 x instrument ...
DAWN-ADAQ
ADAQ data logger with CANBUS input suitable for LPMS CANBUS output, logs up to 8 LPMS IMU parameters such as euler angles, x,y,z, linear acceleration, gyro rates and heave motion. The logger also has 10 analogue inputs suitable for a wide range of sensors for load, pressure, temperature, displacement etc. ...
GS-31
GEN II radio transmitter for one external thermistor inputs. Temperature probes, range -50 to +150°C, Resolution 0.2°C and Accuracy ±0.4°C (-40 to +125°C). Supplied with 4 x AA Alkaline batteries and stub antenna. ...
GS-AC50A
GS-AC50A Clamp-on AC Current Sensor. Range 0-50A RMS. Accuracy ±2%FS ±1 digit. Current clamp comes with 200mm cable for connection to the GS-DPA-AC module. ...
95.0313
MiniAir20 Mini Steel vane anemometer. Air velocity range 0.8-40m/s with accuracy ±1.0% of full scale, ±2.0% of reading. Sensing head 22mm diameter x 28mm, probe length 182mm. Sensor is supplied with 1.8m cable and connector for interfacing with MC20 and MC 4.0 Displays with Lemo Connectors. Steel sensing head screwed to shaft with metal blade turbine suitable for aggressive gas flows. Operating range -30 to +140°C. Part Ref MINI20254 ...
GS-AC100A
GS-AC100A Clamp-on AC Current Sensor. Range 0-100A RMS. Accuracy ±2%FS ±1 digit. Current clamp comes with 200mm cable for connection to the GS-DPA-AC module. ...
GS-AC200A
GS-AC200A Clamp-on AC Current Sensor. Range 0-200A RMS. Accuracy ±2%FS ±1 digit. Current clamp comes with 200mm cable for connection to the GS-DPA-AC module. ...
DC100A
DC current sensor, range 100 amps, accuracy 1% of reading, response time 2ms from 10% to 90% of full scale. Operating temperature -40 to +80 C. Power supply 5vDC, Output 0.5-4.5vDC (0 amps = 2.5v). Accepts ring terminals for two 1/4-20 studs, supplied with 10ft cable. ...
DC150A
DC current sensor, range 150 amps, accuracy 1% of reading, response time 2ms from 10% to 90% of full scale. Operating temperature -40 to +80 C. Power supply 5vDC, Output 0.5-4.5vDC (0 amps = 2.5v). Accepts ring terminals for two 1/4-20 studs, supplied with 10ft cable. ...
DC200A
DC current sensor, range 200 amps, accuracy 1% of reading, response time 2ms from 10% to 90% of full scale. Operating temperature -40 to +80 C. Power supply 5vDC, Output 0.5-4.5vDC (0 amps = 2.5v). Accepts ring terminals for two 1/4-20 studs, supplied with 10ft cable. ...
0367710
Pyrheliometer Mounting Kit. To mount a CHP1/SHP1 series pyrheliometer to the side plate of the 2AP or Solys 2 Suntracker. ...
ComNav G3B GNSS Satellite with G2B Compass Differential GPS (DGPS) correction, G3 Colour Display and 15m cable. Output: NMEA0183. Update rate: Heading & position updates at up to 20 times per second, and can operate at sustained turn rates up to 90° per second. Power Supply 10 to 36vDC (250mA ...
GEN II radio transmitter for an external thermistor probe. Temperature Range -40 to +70°C, Resolution 0.1°C and Accuracy ±0.2°C (-15 to 40°C). Supplied with 4 x AA Alkaline batteries and stub antenna. ...
GS-DPA-AC Dual Port Adapter Input Module for AC current sensors. The GS-DPA-AC can measure electric power current by connecting an AC current sensor (50A clamp/GS-AC50A; 100A clamp/GS-AC100A; 200A clamp/GS-AC200A) single-phase 2 wire, single-phase 3 wire, three-phase 3 wire, to the GL100 Data Logger. Each adapter can be used with up ...
The POC module is meant as Pen Offset High current shunt for recorder ranges of 100mV or 200mV. Maximum continuous current is 16A. Peak current is 20A for 2 min. The shunt has no thermal or current protection and is tested for frequencies below 20 kHz. Fast mounting on all ...
This module transforms a 0-20 mA signal into a Voltage output by means of a highly accurate resistor (125 Ohm). Full accuracy is guaranteed over the recorder temperature range. ...
This module transforms a 4-20 mA signal into a Voltage output by means of a highly accurate resistor (125 Ohm). Full accuracy is guaranteed over the recorder temperature range. ...
ComNav G3B GNSS Satellite with G2B Compass Differential GPS (DGPS) correction, G3 Colour Display and 30m cable. Output: NMEA0183. Update rate: Heading & position updates at up to 20 times per second, and can operate at sustained turn rates up to 90° per second. Power Supply 10 to 36vDC (250mA ...
DACON8-UMB module will convert up to 8 UMB channels into current (0/4-20mA) or voltage (0/2 to 10V) outputs. Fully Configurable using UMB-Config-Tool ...
DARCA Software is used with the GEN II telemetry systems to help manage and analyse the data collected from the various different GEN II transmitters. DARCA Lite, DARCA Plus, DARCA Heritage and DARCA Secure. The table below shows a breakdown of the different versions and what each can provide. ...
Small data buoy, rotationally moulded polyethylene hull with integral ballast skirt. Diameter 0.7m. Buoyancy 50kg. Weight Approx.40kg. Including top frame with Marker Beacon (1NM, yellow -flashes 5 in every 20 secs), 2 x 14W Solar Panels. Sealed waterproof electronics canister containing 24Ah LiPo Battery Pack includes bulkheads for Solar input, ...
ADAQ data logger with CANBUS input suitable for LPMS CANBUS output, logs up to 8 LPMS IMU parameters such as euler angles, x,y,z, linear acceleration, gyro rates and heave motion. The logger also has 10 analogue inputs suitable for a wide range of sensors for load, pressure, temperature, displacement etc. ...
GEN II radio transmitter for one external thermistor inputs. Temperature probes, range -50 to +150°C, Resolution 0.2°C and Accuracy ±0.4°C (-40 to +125°C). Supplied with 4 x AA Alkaline batteries and stub antenna. ...
GS-AC50A Clamp-on AC Current Sensor. Range 0-50A RMS. Accuracy ±2%FS ±1 digit. Current clamp comes with 200mm cable for connection to the GS-DPA-AC module. ...
MiniAir20 Mini Steel vane anemometer. Air velocity range 0.8-40m/s with accuracy ±1.0% of full scale, ±2.0% of reading. Sensing head 22mm diameter x 28mm, probe length 182mm. Sensor is supplied with 1.8m cable and connector for interfacing with MC20 and MC 4.0 Displays with Lemo Connectors. Steel sensing head screwed ...
GS-AC100A Clamp-on AC Current Sensor. Range 0-100A RMS. Accuracy ±2%FS ±1 digit. Current clamp comes with 200mm cable for connection to the GS-DPA-AC module. ...
GS-AC200A Clamp-on AC Current Sensor. Range 0-200A RMS. Accuracy ±2%FS ±1 digit. Current clamp comes with 200mm cable for connection to the GS-DPA-AC module. ...
DC current sensor, range 100 amps, accuracy 1% of reading, response time 2ms from 10% to 90% of full scale. Operating temperature -40 to +80 C. Power supply 5vDC, Output 0.5-4.5vDC (0 amps = 2.5v). Accepts ring terminals for two 1/4-20 studs, supplied with 10ft cable. ...
DC current sensor, range 150 amps, accuracy 1% of reading, response time 2ms from 10% to 90% of full scale. Operating temperature -40 to +80 C. Power supply 5vDC, Output 0.5-4.5vDC (0 amps = 2.5v). Accepts ring terminals for two 1/4-20 studs, supplied with 10ft cable. ...
DC current sensor, range 200 amps, accuracy 1% of reading, response time 2ms from 10% to 90% of full scale. Operating temperature -40 to +80 C. Power supply 5vDC, Output 0.5-4.5vDC (0 amps = 2.5v). Accepts ring terminals for two 1/4-20 studs, supplied with 10ft cable. ...
Need help with your products or have a question for us on our custom systems? Use the form below to send us a message and our experts will be in touch to help.
