Products

Grid View
List View

Edit Content

SGW1-IA3-MB-HL Modbus ASCII/RTU to Hostlink Converter

SGW1-IA3-MB-HL converts an OMRON PLC (Hostlink Protocol) into a Modbus ASCII/RTU Slave easily. Using SGW1-MB-HL you can connect an OMRON PLC to a Modbus Network. Protocol conversion is based on easy-to-fill translation tables. EG: You can read OMRON registers DM0100 to DM0199 through Modbus registers 40100 to 40199. ...

VLS/DA1/LSR/003

VLS/DA1/LSR/003 Optical Speed Sensor with a red laser class II 635nm light source. Optical Range: 50 - 2,000mm with Green LED on target indicator. Overall speed range 50-60,000 RPM. Analogue Output: 0-6V for 0 to 6,000 RPM (Range 1), 0 to 60,000 RPM (Range 2). Optical Angle: up to ±80°. ...

1657437

Single Output General Purpose Enclosed Power Supply, Ref LS50-12. Input supply 88-264 VAC, output 12 vDC at 4.2 amps. Chassis mounting type. ...

400.0312

MC 4.0 ManoAir Manometer Display and 4,000mAh Lithium Polymer Battery. Range ±20kPa. The MC 4.0 can measure absolute or differential pressures, filter and pitot tubes for ventiliation ducts. Measurement Range ±20kPa. Resolution: 0.01kPa, Accuracy: <100 Pa ± 0.03kPa + ±0.10%FS >100 Pa ±0.01kPa + ±0.10%FS. 3.2" TFT-Display, 2Hz measurement rate, ...

CA-12/0090D

Solar Mounting Kit for two 90W Ameresco Solar Panel U-bolts are required for pole mounting ...

CCDDT-25T-LOADCAP

Spherical Load Cap for CCDDT Load Cells. Capacity up to 25 Tonnes. Dimensions: Diameter 60mm, Height 15mm, Internal Radius 76mm ...

EL-PDF-1-004

EasyLog PDF Temperature Logger for Ambient Pharmaceuticals. Temperature Range: -30 to +60°C. Alarm Thresholds: Low: +8°C; High +25°C. Logging Interval: 10 Mins, Internal Memory: 32,600 readings (220 days logging). Battery Life: 12 Months. Start/Stop and Status button to light LEDs in the event of any alarm conditions. No software required. ...

LEO1EI-700BAR

LEO1EI Digital Manometer suitable for Hazardous Areas. Range 0 to 700 Bar with accuracy of 0.2% and peak reading mode at 5kHz. Pressure connection 1/4 inch BSP male connection, operating temperature 0 to 50 C, internal battery for up to 1,000 hours operation (150 hours in peak mode) and IP65 ...

MX16-A-200-0-0-0

MX16 Gas Detection Controller configured for 4-20mA Analogue Input Gas Detector. Pre-Configured for Oxygen (O2) with a range of 0-30% Volume. 2 Alarm levels (Al1, Al2) + 1 fault, with Dry Contact Relays. LCD back-lit display. IP55 Enclosure with 3 x M16 and 2 x M20 cable glands. Dimensions 265 ...

OSBKT Single-Ended Shear Beam Load Cell

The OSBKT single-ended shear beam load cell are suitable for medium capacity weighing applications such as hoppers and vessels where a high accuracy measurement system is required. The high integrity IP67 body and alloy steel construction make it ideal for general purpose industrial weighing applications. Ranges 250kg to 2000kg. The ...

PL-525-0.6-V

PL-525 Relative Low Range Pressure Transmitter. Range 0 to 600mBar. Power Supply 12-33vDC, output 0-10vDC. IP65 stainless steel casing with ½" BSP male thread pressure connection, ceramic diaphragm and DIN connector. Operating temperature range -15 to +80°C. ...

PL-692-1-V

PL-692-1-V differential pressure transmitter suitable for liquids, steam and gases. Pressure range 0-1 BarD over a 0-10V output with 18-33vDC power supply. IP65 stainless steel casing with a pair of 6mm compression pressure connection, ceramic Al₂O₃ (96%) diaphragm and 1.5m flying lead. Operating temperature range -15 to +85°C. ...

CA-12/0140D

Solar Mounting Kit for two 140W Ameresco Solar Panel U-bolts are required for pole mounting ...

CCDDT-50T-LOADCAP

Spherical Load Cap for CCDDT Load Cells. Capacity up to 50 Tonnes. Dimensions: Diameter 88mm, Height 20mm, Internal Radius 159mm ...

LEO1EI-1000BAR

LEO1EI Digital Manometer suitable for Hazardous Areas. Range 0 to 1,000 Bar with accuracy of 0.2% and peak reading mode at 5kHz. Pressure connection 1/4 inch BSP male connection, operating temperature 0 to 50 C, internal battery for up to 1,000 hours operation (150 hours in peak mode) and IP65 ...

MX16-A-239-0-0-0

MX16 Gas Detection Controller configured for 4-20mA Analogue Input Gas Detector. Pre-Configured for Carbon Dioxide (CO2) with a range of 0-5% Volume. 2 Alarm levels (Al1, Al2) + 1 fault, with Dry Contact Relays. LCD back-lit display. IP55 Enclosure with 3 x M16 and 2 x M20 cable glands. Dimensions ...

OSBST Single-Ended Shear Beam Load Cell

The OSBST single-ended shear beam load cell are suitable for medium capacity weighing applications such as hoppers and vessels where a high accuracy measurement system is required. The waterproof IP68 body and stainless steel construction make it ideal for conveyor weighing applications where the loadcell may need to be washed ...

PL-692-2.5-V

PL-692-2.5-V differential pressure transmitter suitable for liquids, steam and gases. Pressure range 0-2.5 BarD over a 0-10V output with 18-33vDC power supply. IP65 stainless steel casing with a pair of 6mm compression pressure connection, ceramic Al₂O₃ (96%) diaphragm and 1.5m flying lead. Operating temperature range -15 to +85°C. ...

CCDDT-100T-LOADCAP

Spherical Load Cap for CCDDT Load Cells. Capacity up to 100 Tonnes. Dimensions: Diameter 101mm, Height 30mm, Internal Radius 151mm ...

CP11

CP11 handheld temperature, relative humidity and CO2 instrument. Range -20 to +60°C, 0-100%RH & 0-9999ppm. Psychrometric calculations of Dew Point and Wet Bulb Temperature. CP11 will log up to 18,000 time stamped values. Powered by 4 x AA batteries, or AC Mains Adapter. ABS housing, dimensions 76.7 x 41.8 x ...

MF96421

Nemo 96HDLe Multi-function panel mounted power meter suitable for single or 3 phase networks, 3 or 4-wires. Single-phase Input: 50-290V. Three-phase Input: 80-500V (phase-phase). Current Inputs 1A or 5A CTs. Meter has 1 slot for a plug in module. Auxiliary Power Supply: 80-265vAC/100-300vDC. Backlit LCD display with 8/12mm digits. Dimensions ...

MT Series Peak-Echo Ultrasonic Thickness Meter

The MT Series are a range of sophisticated digital ultrasonic thickness gauge designed for single thickness measurements. Operating on a pulse-echo principle, it precisely measures material thickness by calculating the transit time of ultrasonic pulses. Its key technical features include compatibility with various ultrasonic conductors, dual straight beam probes for ...

Multi-Parameter Wall Mounted Display

The CL11 benchtop display unit is an inexpensive multiple parameter meter that simultaneously measures and records CO2, humidity and temperature. The CO2 DISPLAY is a similar wall, or bench top mounted display. Equipped with the field-tested ROTRONIC HYGROMER IN-1 humidity sensor, this instrument offers unbeatable value for money. Using the ...

PL-692-4-V

PL-692-4-V differential pressure transmitter suitable for liquids, steam and gases. Pressure range 0-4 BarD over a 0-10V output with 18-33vDC power supply. IP65 stainless steel casing with a pair of 6mm compression pressure connection, ceramic Al₂O₃ (96%) diaphragm and 1.5m flying lead. Operating temperature range -15 to +85°C. ...

Edit Content

SGW1-IA3-MB-HL Modbus ASCII/RTU to Hostlink Converter

SGW1-IA3-MB-HL converts an OMRON PLC (Hostlink Protocol) into a Modbus ASCII/RTU Slave easily. Using SGW1-MB-HL you can connect an OMRON PLC to a Modbus Network. Protocol conversion is based on easy-to-fill translation tables. EG: You can read OMRON registers DM0100 to DM0199 through Modbus registers 40100 to 40199. ...

VLS/DA1/LSR/003

VLS/DA1/LSR/003 Optical Speed Sensor with a red laser class II 635nm light source. Optical Range: 50 - 2,000mm with Green LED on target indicator. Overall speed range 50-60,000 RPM. Analogue Output: 0-6V for 0 to 6,000 RPM (Range 1), 0 to 60,000 RPM (Range 2). Optical Angle: up to ±80°. Power Supply: 7.5 to 15vDC. Dimensions: Length 130mm x Diameter 34mm. Operating Temperature -10 to + 70°C. 15m cable with flying leads. ...

1657437

Single Output General Purpose Enclosed Power Supply, Ref LS50-12. Input supply 88-264 VAC, output 12 vDC at 4.2 amps. Chassis mounting type. ...

400.0312

MC 4.0 ManoAir Manometer Display and 4,000mAh Lithium Polymer Battery. Range ±20kPa. The MC 4.0 can measure absolute or differential pressures, filter and pitot tubes for ventiliation ducts. Measurement Range ±20kPa. Resolution: 0.01kPa, Accuracy: <100 Pa ± 0.03kPa + ±0.10%FS >100 Pa ±0.01kPa + ±0.10%FS. 3.2" TFT-Display, 2Hz measurement rate, internal logger for up to 1 million readings and bluetooth connectivity. Dimensions: 168 x 68 x 38mm, Weight 300g, IP67 with a removeable green rubber ...

CA-12/0090D

Solar Mounting Kit for two 90W Ameresco Solar Panel U-bolts are required for pole mounting ...

CCDDT-25T-LOADCAP

Spherical Load Cap for CCDDT Load Cells. Capacity up to 25 Tonnes. Dimensions: Diameter 60mm, Height 15mm, Internal Radius 76mm ...

EL-PDF-1-004

EasyLog PDF Temperature Logger for Ambient Pharmaceuticals. Temperature Range: -30 to +60°C. Alarm Thresholds: Low: +8°C; High +25°C. Logging Interval: 10 Mins, Internal Memory: 32,600 readings (220 days logging). Battery Life: 12 Months. Start/Stop and Status button to light LEDs in the event of any alarm conditions. No software required. Results appear in an automatically generated PDF file. Sold as a pack of 10 loggers. ...

LEO1EI-700BAR

LEO1EI Digital Manometer suitable for Hazardous Areas. Range 0 to 700 Bar with accuracy of 0.2% and peak reading mode at 5kHz. Pressure connection 1/4 inch BSP male connection, operating temperature 0 to 50 C, internal battery for up to 1,000 hours operation (150 hours in peak mode) and IP65 casing. ...

MX16-A-200-0-0-0

MX16 Gas Detection Controller configured for 4-20mA Analogue Input Gas Detector. Pre-Configured for Oxygen (O2) with a range of 0-30% Volume. 2 Alarm levels (Al1, Al2) + 1 fault, with Dry Contact Relays. LCD back-lit display. IP55 Enclosure with 3 x M16 and 2 x M20 cable glands. Dimensions 265 x 266 x 96mm. The MX16 is delivered alone and does not include a detector. WCDCOM16 Software Pack allows for re-configuration. ...

OSBKT Single-Ended Shear Beam Load Cell

The OSBKT single-ended shear beam load cell are suitable for medium capacity weighing applications such as hoppers and vessels where a high accuracy measurement system is required. The high integrity IP67 body and alloy steel construction make it ideal for general purpose industrial weighing applications. Ranges 250kg to 2000kg. The load cells provide a 2mV/V output but can be supplied with suitable inline amplifiers to provide a calibrated 4-20mA output. ATEX versions are available. ...

PL-525-0.6-V

PL-525 Relative Low Range Pressure Transmitter. Range 0 to 600mBar. Power Supply 12-33vDC, output 0-10vDC. IP65 stainless steel casing with ½" BSP male thread pressure connection, ceramic diaphragm and DIN connector. Operating temperature range -15 to +80°C. ...

PL-692-1-V

PL-692-1-V differential pressure transmitter suitable for liquids, steam and gases. Pressure range 0-1 BarD over a 0-10V output with 18-33vDC power supply. IP65 stainless steel casing with a pair of 6mm compression pressure connection, ceramic Al₂O₃ (96%) diaphragm and 1.5m flying lead. Operating temperature range -15 to +85°C. ...

CA-12/0140D

Solar Mounting Kit for two 140W Ameresco Solar Panel U-bolts are required for pole mounting ...

CCDDT-50T-LOADCAP

Spherical Load Cap for CCDDT Load Cells. Capacity up to 50 Tonnes. Dimensions: Diameter 88mm, Height 20mm, Internal Radius 159mm ...

LEO1EI-1000BAR

LEO1EI Digital Manometer suitable for Hazardous Areas. Range 0 to 1,000 Bar with accuracy of 0.2% and peak reading mode at 5kHz. Pressure connection 1/4 inch BSP male connection, operating temperature 0 to 50 C, internal battery for up to 1,000 hours operation (150 hours in peak mode) and IP65 casing. ...

MX16-A-239-0-0-0

MX16 Gas Detection Controller configured for 4-20mA Analogue Input Gas Detector. Pre-Configured for Carbon Dioxide (CO2) with a range of 0-5% Volume. 2 Alarm levels (Al1, Al2) + 1 fault, with Dry Contact Relays. LCD back-lit display. IP55 Enclosure with 3 x M16 and 2 x M20 cable glands. Dimensions 265 x 266 x 96mm. The MX16 is delivered alone and does not include a detector. WCDCOM16 Software Pack allows for re-configuration. ...

OSBST Single-Ended Shear Beam Load Cell

The OSBST single-ended shear beam load cell are suitable for medium capacity weighing applications such as hoppers and vessels where a high accuracy measurement system is required. The waterproof IP68 body and stainless steel construction make it ideal for conveyor weighing applications where the loadcell may need to be washed down for hygienic purposes, eg. food, pharmaceutical or brewing industry.. Ranges 500kg to 5000kg. The load cells provide a 2mV/V output but can be supplied ...

PL-692-2.5-V

PL-692-2.5-V differential pressure transmitter suitable for liquids, steam and gases. Pressure range 0-2.5 BarD over a 0-10V output with 18-33vDC power supply. IP65 stainless steel casing with a pair of 6mm compression pressure connection, ceramic Al₂O₃ (96%) diaphragm and 1.5m flying lead. Operating temperature range -15 to +85°C. ...

CCDDT-100T-LOADCAP

Spherical Load Cap for CCDDT Load Cells. Capacity up to 100 Tonnes. Dimensions: Diameter 101mm, Height 30mm, Internal Radius 151mm ...

CP11

CP11 handheld temperature, relative humidity and CO2 instrument. Range -20 to +60°C, 0-100%RH & 0-9999ppm. Psychrometric calculations of Dew Point and Wet Bulb Temperature. CP11 will log up to 18,000 time stamped values. Powered by 4 x AA batteries, or AC Mains Adapter. ABS housing, dimensions 76.7 x 41.8 x 233.9mm. ...

MF96421

Nemo 96HDLe Multi-function panel mounted power meter suitable for single or 3 phase networks, 3 or 4-wires. Single-phase Input: 50-290V. Three-phase Input: 80-500V (phase-phase). Current Inputs 1A or 5A CTs. Meter has 1 slot for a plug in module. Auxiliary Power Supply: 80-265vAC/100-300vDC. Backlit LCD display with 8/12mm digits. Dimensions 96 x 96mm flush mounting. The Nemo 96HDLe provides a Pulse Output for active or reactive energy counting and RS485 Modbus RTU Comms ...

MT Series Peak-Echo Ultrasonic Thickness Meter

The MT Series are a range of sophisticated digital ultrasonic thickness gauge designed for single thickness measurements. Operating on a pulse-echo principle, it precisely measures material thickness by calculating the transit time of ultrasonic pulses. Its key technical features include compatibility with various ultrasonic conductors, dual straight beam probes for diverse applications, and an advanced error correction system. The device boasts zero and two-point calibration, real-time coupling status indication, and a backlight for low-light conditions. ...

Multi-Parameter Wall Mounted Display

The CL11 benchtop display unit is an inexpensive multiple parameter meter that simultaneously measures and records CO2, humidity and temperature. The CO2 DISPLAY is a similar wall, or bench top mounted display. Equipped with the field-tested ROTRONIC HYGROMER IN-1 humidity sensor, this instrument offers unbeatable value for money. Using the ROTRONIC software HW4, it can be easily set to record as required and data can then be downloaded, saved and analysed. Both units also display ...

PL-692-4-V

PL-692-4-V differential pressure transmitter suitable for liquids, steam and gases. Pressure range 0-4 BarD over a 0-10V output with 18-33vDC power supply. IP65 stainless steel casing with a pair of 6mm compression pressure connection, ceramic Al₂O₃ (96%) diaphragm and 1.5m flying lead. Operating temperature range -15 to +85°C. ...

SGW1-IA3-MB-HL Modbus ASCII/RTU to Hostlink Converter

SGW1-IA3-MB-HL converts an OMRON PLC (Hostlink Protocol) into a Modbus ASCII/RTU Slave easily. Using SGW1-MB-HL you can connect an OMRON PLC to a Modbus Network. Protocol conversion is based on easy-to-fill translation tables. EG: You can read OMRON registers DM0100 to DM0199 through Modbus registers 40100 to 40199. ...

VLS/DA1/LSR/003

VLS/DA1/LSR/003 Optical Speed Sensor with a red laser class II 635nm light source. Optical Range: 50 - 2,000mm with Green LED on target indicator. Overall speed range 50-60,000 RPM. Analogue Output: 0-6V for 0 to 6,000 RPM (Range 1), 0 to 60,000 RPM (Range 2). Optical Angle: up to ±80°. ...

1657437

Single Output General Purpose Enclosed Power Supply, Ref LS50-12. Input supply 88-264 VAC, output 12 vDC at 4.2 amps. Chassis mounting type. ...

400.0312

MC 4.0 ManoAir Manometer Display and 4,000mAh Lithium Polymer Battery. Range ±20kPa. The MC 4.0 can measure absolute or differential pressures, filter and pitot tubes for ventiliation ducts. Measurement Range ±20kPa. Resolution: 0.01kPa, Accuracy: <100 Pa ± 0.03kPa + ±0.10%FS >100 Pa ±0.01kPa + ±0.10%FS. 3.2" TFT-Display, 2Hz measurement rate, ...

CA-12/0090D

Solar Mounting Kit for two 90W Ameresco Solar Panel U-bolts are required for pole mounting ...

CCDDT-25T-LOADCAP

Spherical Load Cap for CCDDT Load Cells. Capacity up to 25 Tonnes. Dimensions: Diameter 60mm, Height 15mm, Internal Radius 76mm ...

EL-PDF-1-004

EasyLog PDF Temperature Logger for Ambient Pharmaceuticals. Temperature Range: -30 to +60°C. Alarm Thresholds: Low: +8°C; High +25°C. Logging Interval: 10 Mins, Internal Memory: 32,600 readings (220 days logging). Battery Life: 12 Months. Start/Stop and Status button to light LEDs in the event of any alarm conditions. No software required. ...

LEO1EI-700BAR

LEO1EI Digital Manometer suitable for Hazardous Areas. Range 0 to 700 Bar with accuracy of 0.2% and peak reading mode at 5kHz. Pressure connection 1/4 inch BSP male connection, operating temperature 0 to 50 C, internal battery for up to 1,000 hours operation (150 hours in peak mode) and IP65 ...

MX16-A-200-0-0-0

MX16 Gas Detection Controller configured for 4-20mA Analogue Input Gas Detector. Pre-Configured for Oxygen (O2) with a range of 0-30% Volume. 2 Alarm levels (Al1, Al2) + 1 fault, with Dry Contact Relays. LCD back-lit display. IP55 Enclosure with 3 x M16 and 2 x M20 cable glands. Dimensions 265 ...

OSBKT Single-Ended Shear Beam Load Cell

The OSBKT single-ended shear beam load cell are suitable for medium capacity weighing applications such as hoppers and vessels where a high accuracy measurement system is required. The high integrity IP67 body and alloy steel construction make it ideal for general purpose industrial weighing applications. Ranges 250kg to 2000kg. The ...

PL-525-0.6-V

PL-525 Relative Low Range Pressure Transmitter. Range 0 to 600mBar. Power Supply 12-33vDC, output 0-10vDC. IP65 stainless steel casing with ½" BSP male thread pressure connection, ceramic diaphragm and DIN connector. Operating temperature range -15 to +80°C. ...

PL-692-1-V

PL-692-1-V differential pressure transmitter suitable for liquids, steam and gases. Pressure range 0-1 BarD over a 0-10V output with 18-33vDC power supply. IP65 stainless steel casing with a pair of 6mm compression pressure connection, ceramic Al₂O₃ (96%) diaphragm and 1.5m flying lead. Operating temperature range -15 to +85°C. ...

CA-12/0140D

Solar Mounting Kit for two 140W Ameresco Solar Panel U-bolts are required for pole mounting ...

CCDDT-50T-LOADCAP

Spherical Load Cap for CCDDT Load Cells. Capacity up to 50 Tonnes. Dimensions: Diameter 88mm, Height 20mm, Internal Radius 159mm ...

LEO1EI-1000BAR

LEO1EI Digital Manometer suitable for Hazardous Areas. Range 0 to 1,000 Bar with accuracy of 0.2% and peak reading mode at 5kHz. Pressure connection 1/4 inch BSP male connection, operating temperature 0 to 50 C, internal battery for up to 1,000 hours operation (150 hours in peak mode) and IP65 ...

MX16-A-239-0-0-0

MX16 Gas Detection Controller configured for 4-20mA Analogue Input Gas Detector. Pre-Configured for Carbon Dioxide (CO2) with a range of 0-5% Volume. 2 Alarm levels (Al1, Al2) + 1 fault, with Dry Contact Relays. LCD back-lit display. IP55 Enclosure with 3 x M16 and 2 x M20 cable glands. Dimensions ...

OSBST Single-Ended Shear Beam Load Cell

The OSBST single-ended shear beam load cell are suitable for medium capacity weighing applications such as hoppers and vessels where a high accuracy measurement system is required. The waterproof IP68 body and stainless steel construction make it ideal for conveyor weighing applications where the loadcell may need to be washed ...

PL-692-2.5-V

PL-692-2.5-V differential pressure transmitter suitable for liquids, steam and gases. Pressure range 0-2.5 BarD over a 0-10V output with 18-33vDC power supply. IP65 stainless steel casing with a pair of 6mm compression pressure connection, ceramic Al₂O₃ (96%) diaphragm and 1.5m flying lead. Operating temperature range -15 to +85°C. ...

CCDDT-100T-LOADCAP

Spherical Load Cap for CCDDT Load Cells. Capacity up to 100 Tonnes. Dimensions: Diameter 101mm, Height 30mm, Internal Radius 151mm ...

CP11

CP11 handheld temperature, relative humidity and CO2 instrument. Range -20 to +60°C, 0-100%RH & 0-9999ppm. Psychrometric calculations of Dew Point and Wet Bulb Temperature. CP11 will log up to 18,000 time stamped values. Powered by 4 x AA batteries, or AC Mains Adapter. ABS housing, dimensions 76.7 x 41.8 x ...

MF96421

Nemo 96HDLe Multi-function panel mounted power meter suitable for single or 3 phase networks, 3 or 4-wires. Single-phase Input: 50-290V. Three-phase Input: 80-500V (phase-phase). Current Inputs 1A or 5A CTs. Meter has 1 slot for a plug in module. Auxiliary Power Supply: 80-265vAC/100-300vDC. Backlit LCD display with 8/12mm digits. Dimensions ...

MT Series Peak-Echo Ultrasonic Thickness Meter

The MT Series are a range of sophisticated digital ultrasonic thickness gauge designed for single thickness measurements. Operating on a pulse-echo principle, it precisely measures material thickness by calculating the transit time of ultrasonic pulses. Its key technical features include compatibility with various ultrasonic conductors, dual straight beam probes for ...

Multi-Parameter Wall Mounted Display

The CL11 benchtop display unit is an inexpensive multiple parameter meter that simultaneously measures and records CO2, humidity and temperature. The CO2 DISPLAY is a similar wall, or bench top mounted display. Equipped with the field-tested ROTRONIC HYGROMER IN-1 humidity sensor, this instrument offers unbeatable value for money. Using the ...

PL-692-4-V

PL-692-4-V differential pressure transmitter suitable for liquids, steam and gases. Pressure range 0-4 BarD over a 0-10V output with 18-33vDC power supply. IP65 stainless steel casing with a pair of 6mm compression pressure connection, ceramic Al₂O₃ (96%) diaphragm and 1.5m flying lead. Operating temperature range -15 to +85°C. ...

Contact us

8:30 AM to 5 PM Monday to Thursday
8:30 AM to 3 PM on Friday.

A real person will answer the phone and deal with your enquiry

omni instruments | sensors and data acquisition equipment

Sales & Technical Support

Products

SGW1-IA3-MB-HL Modbus ASCII/RTU to Hostlink Converter

VLS/DA1/LSR/003

1657437

400.0312

CA-12/0090D

CCDDT-25T-LOADCAP

EL-PDF-1-004

LEO1EI-700BAR

MX16-A-200-0-0-0

OSBKT Single-Ended Shear Beam Load Cell

PL-525-0.6-V

PL-692-1-V

CA-12/0140D

CCDDT-50T-LOADCAP

LEO1EI-1000BAR

MX16-A-239-0-0-0

OSBST Single-Ended Shear Beam Load Cell

PL-692-2.5-V

CCDDT-100T-LOADCAP

CP11

MF96421

MT Series Peak-Echo Ultrasonic Thickness Meter

Multi-Parameter Wall Mounted Display

PL-692-4-V

SGW1-IA3-MB-HL Modbus ASCII/RTU to Hostlink Converter

VLS/DA1/LSR/003

1657437

400.0312

CA-12/0090D

CCDDT-25T-LOADCAP

EL-PDF-1-004

LEO1EI-700BAR

MX16-A-200-0-0-0

OSBKT Single-Ended Shear Beam Load Cell

PL-525-0.6-V

PL-692-1-V

CA-12/0140D

CCDDT-50T-LOADCAP

LEO1EI-1000BAR

MX16-A-239-0-0-0

OSBST Single-Ended Shear Beam Load Cell

PL-692-2.5-V

CCDDT-100T-LOADCAP

CP11

MF96421

MT Series Peak-Echo Ultrasonic Thickness Meter

Multi-Parameter Wall Mounted Display

PL-692-4-V

SGW1-IA3-MB-HL Modbus ASCII/RTU to Hostlink Converter

VLS/DA1/LSR/003

1657437

400.0312

CA-12/0090D

CCDDT-25T-LOADCAP

EL-PDF-1-004

LEO1EI-700BAR

MX16-A-200-0-0-0

OSBKT Single-Ended Shear Beam Load Cell

PL-525-0.6-V

PL-692-1-V

CA-12/0140D

CCDDT-50T-LOADCAP

LEO1EI-1000BAR

MX16-A-239-0-0-0

OSBST Single-Ended Shear Beam Load Cell

PL-692-2.5-V

CCDDT-100T-LOADCAP

CP11

MF96421

MT Series Peak-Echo Ultrasonic Thickness Meter

Multi-Parameter Wall Mounted Display

PL-692-4-V

Contact us

8:30 AM to 5 PM Monday to Thursday8:30 AM to 3 PM on Friday.

We are here to help

Enquire now

8:30 AM to 5 PM Monday to Thursday
8:30 AM to 3 PM on Friday.