The WD-AMX range of water leak detection modules are designed for use with the WD-CS, WD-PS and WD-RS range of water leak detection sensors. They are suitable for DIN-rail mounting inside AHUs, power distribution units or general areas where leak detection is required. ...
The WLM4 Water Leak Detection Module has 4 input channels with zone indication and 1 common output with fault indication. DIN Rail or wall mount options. The WLM can be used with a combination of water detection sensors. ...
Our water leak detection cable is typically used to detect water leaks under floors but may also be used to detect water levels rising by fitting cable along a wall or surface. Water leak detection cable is designed to be used in conjunction with controller modules, but a relay output ...
The water leak detection point sensors are typically used to detect water at a localised point but may also be used to detect water levels rising by fitting at the required level on a wall or surface. Water detection point sensor is designed to be used in conjunction with a ...
This Condensation Prevention Sensor is designed to meet the requirements for a low cost device capable of providing early warning of the onset of condensing conditions. Applications include chilled beam/ceiling systems where control safeguards are required to avoid indoor rain. The sensor provides either a volt-free changeover contact or current ...
The WD-RS rain sensors can be combined with the WD-AMX alarm units to provide an output on the first signs of rain. This can be used to automate the closure of windows on the first drops of rain. The WD-AMX alarm unit includes a 250vAC @ 12A relay that can ...
The WD-AMX range of water leak detection modules are designed for use with the WD-CS, WD-PS and WD-RS range of water leak detection sensors. They are suitable for DIN-rail mounting inside AHUs, power distribution units or general areas where leak detection is required. ...
WLM4 – Four Channel Water Leak Detection Module
The WLM4 Water Leak Detection Module has 4 input channels with zone indication and 1 common output with fault indication. DIN Rail or wall mount options. The WLM can be used with a combination of water detection sensors. ...
Water Leak Detection Cable WD-CS
Our water leak detection cable is typically used to detect water leaks under floors but may also be used to detect water levels rising by fitting cable along a wall or surface. Water leak detection cable is designed to be used in conjunction with controller modules, but a relay output from the controller can connect to a Building Management System. Optional fixing clips are available. ...
Water Leak Detection Point Sensor WD-PS
The water leak detection point sensors are typically used to detect water at a localised point but may also be used to detect water levels rising by fitting at the required level on a wall or surface. Water detection point sensor is designed to be used in conjunction with a WD-AMX controller module. ...
Condensation Prevention Sensor WD-CPS
This Condensation Prevention Sensor is designed to meet the requirements for a low cost device capable of providing early warning of the onset of condensing conditions. Applications include chilled beam/ceiling systems where control safeguards are required to avoid indoor rain. The sensor provides either a volt-free changeover contact or current output and is housed in a small enclosure which can be strapped to the chilled surface that requires monitoring. The unit is 24vAC/DC powered ...
Rain Sensor with Integral Heater
The WD-RS rain sensors can be combined with the WD-AMX alarm units to provide an output on the first signs of rain. This can be used to automate the closure of windows on the first drops of rain. The WD-AMX alarm unit includes a 250vAC @ 12A relay that can be used to activate motors to close the windows, or by integration into an existing Building Management System to then control the windows. The WD-RS ...
Water Detection Alarm System WD-AMX
The WD-AMX range of water leak detection modules are designed for use with the WD-CS, WD-PS and WD-RS range of water leak detection sensors. They are suitable for DIN-rail mounting inside AHUs, power distribution units or general areas where leak detection is required. ...
The WLM4 Water Leak Detection Module has 4 input channels with zone indication and 1 common output with fault indication. DIN Rail or wall mount options. The WLM can be used with a combination of water detection sensors. ...
Our water leak detection cable is typically used to detect water leaks under floors but may also be used to detect water levels rising by fitting cable along a wall or surface. Water leak detection cable is designed to be used in conjunction with controller modules, but a relay output ...
The water leak detection point sensors are typically used to detect water at a localised point but may also be used to detect water levels rising by fitting at the required level on a wall or surface. Water detection point sensor is designed to be used in conjunction with a ...
This Condensation Prevention Sensor is designed to meet the requirements for a low cost device capable of providing early warning of the onset of condensing conditions. Applications include chilled beam/ceiling systems where control safeguards are required to avoid indoor rain. The sensor provides either a volt-free changeover contact or current ...
The WD-RS rain sensors can be combined with the WD-AMX alarm units to provide an output on the first signs of rain. This can be used to automate the closure of windows on the first drops of rain. The WD-AMX alarm unit includes a 250vAC @ 12A relay that can ...
Need help with your products or have a question for us on our custom systems? Use the form below to send us a message and our experts will be in touch to help.
