Tinytag CAB-3249 Voltage/Current Input Lead for connection of voltage and current input signals to Tinytag data loggers. Includes a 5-pin connection to logger and 1m flying tails...
Tinytag CAB-3246 Count Input Lead for connection of 2-wire input signals to Tinytag data loggers. Includes a 2-pin connection to logger and 1m flying tails...
General Purpose K-Type Penetration Probe, 100mm x 3.3mm diameter. Supplied with 1 metre PTFE Insulated Lead and a K Therm MiniPlug connector. Probe Temperature Range: -75 to +250°C, Response Time: <5 Seconds. Part Ref 133-158..
5331A3B programmable transmitter with a 7.2-35vDC power supply. Single channel unit for PT100, thermocouple, Resistance or bi-polar mV input, producing a 2-wire 4-20mA output. 1.5kvAC galvanic isolation. Programmed to suit the connected sensor. Transmitter fitted in weatherproof enclosure with 2 cable glands...
This manometer hose set will fit the 9215, 9230 & 9275 series handheld pressure meters. Supplied as 2 x 300 mm lengths x 4mm ID it allows accurate gas pressure testing of heating appliances, flue draught measurement etc...
This manometer hose set will fit the 9205 series handheld pressure meters. Supplied as 2 x 500 mm lengths x 6mm ID it allows accurate gas pressure testing of heating appliances, flue draught measurement etc...
Calibration Certificate for OQ610 Data Logger. OQ610 logger inputs calibrated at 5 points on the T and K type input ranges at 2%, 25%, 50%, 75% and 98% of each range...
SCS Calibration Certificate for MiniAir anemometers, vane anemometers fitted to MiniAir display units and cup anemometers. Price covers a 5 point calibration...
Calibration 2 Axis - Fixed Point (Wind Tunnel). The calibration procedure involves the unit being fixed in one point facing North with a varying wind speed from 0 to 30 or 40m/s. The calibration certificate then compares the wind tunnel velocity readings to those collected by the unit...
Initial Calibration Certificate for Infrared Sensors, PyroMini, PyroCouple and PyroPen. UKAS traceable certificate showing the measured temperature at three points across the sensors temperature range. Only available when ordered along with a brand new sensor...
Licence Key to allow a CMC-99 unit to log data. 1.5GB of internal memory, up to 250 million samples, and a maximum logging speed of 10Hz (limited to a number of recording channels)...
Quick-fit to stainless steel flat base adapter for attachment with epoxy resin. Provides a high rigidity connection but with reduced high frequency response...
Initial Calibration of pressure sensors purchased from Omni Instruments. Pressure Calibration to 5 points. All ranges between -0.8 and 1,000 Bar. Certificate shows actual output readings in graph and table form. Maximum errors shown at each point as a percentage. Certificate is timed, dated and has a unique reference for..
Non-melting hydrocarbon grease. Low contact resistance. 50ml tube. Provides a clear contact from sensor to the surface to improve the ultrasonic signal...
Tinytag CAB-3249 Voltage/Current Input Lead for connection of voltage and current input signals to Tinytag data loggers. Includes a 5-pin connection to logger and 1m flying tails. ...
Tinytag CAB-3246 Count Input Lead for connection of 2-wire input signals to Tinytag data loggers. Includes a 2-pin connection to logger and 1m flying tails. ...
General Purpose K-Type Penetration Probe, 100mm x 3.3mm diameter. Supplied with 1 metre PTFE Insulated Lead and a K Therm MiniPlug connector. Probe Temperature Range: -75 to +250°C, Response Time: <5 Seconds. Part Ref 133-158 ...
5331A3B programmable transmitter with a 7.2-35vDC power supply. Single channel unit for PT100, thermocouple, Resistance or bi-polar mV input, producing a 2-wire 4-20mA output. 1.5kvAC galvanic isolation. Programmed to suit the connected sensor. Transmitter fitted in weatherproof enclosure with 2 cable glands. ...
This manometer hose set will fit the 9215, 9230 & 9275 series handheld pressure meters. Supplied as 2 x 300 mm lengths x 4mm ID it allows accurate gas pressure testing of heating appliances, flue draught measurement etc. ...
This manometer hose set will fit the 9205 series handheld pressure meters. Supplied as 2 x 500 mm lengths x 6mm ID it allows accurate gas pressure testing of heating appliances, flue draught measurement etc. ...
Calibration Certificate for OQ610 Data Logger. OQ610 logger inputs calibrated at 5 points on the T and K type input ranges at 2%, 25%, 50%, 75% and 98% of each range. ...
SCS Calibration Certificate for MiniAir anemometers, vane anemometers fitted to MiniAir display units and cup anemometers. Price covers a 5 point calibration. ...
Calibration 2 Axis - Fixed Point (Wind Tunnel). The calibration procedure involves the unit being fixed in one point facing North with a varying wind speed from 0 to 30 or 40m/s. The calibration certificate then compares the wind tunnel velocity readings to those collected by the unit. ...
Initial Calibration Certificate for Infrared Sensors, PyroMini, PyroCouple and PyroPen. UKAS traceable certificate showing the measured temperature at three points across the sensors temperature range. Only available when ordered along with a brand new sensor. ...
Licence Key to allow a CMC-99 unit to log data. 1.5GB of internal memory, up to 250 million samples, and a maximum logging speed of 10Hz (limited to a number of recording channels). ...
Quick-fit to stainless steel flat base adapter for attachment with epoxy resin. Provides a high rigidity connection but with reduced high frequency response. ...
Initial Calibration of pressure sensors purchased from Omni Instruments. Pressure Calibration to 5 points. All ranges between -0.8 and 1,000 Bar. Certificate shows actual output readings in graph and table form. Maximum errors shown at each point as a percentage. Certificate is timed, dated and has a unique reference for complete traceablility. ...
Non-melting hydrocarbon grease. Low contact resistance. 50ml tube. Provides a clear contact from sensor to the surface to improve the ultrasonic signal. ...
Tinytag CAB-3249 Voltage/Current Input Lead for connection of voltage and current input signals to Tinytag data loggers. Includes a 5-pin connection to logger and 1m flying tails...
Tinytag CAB-3246 Count Input Lead for connection of 2-wire input signals to Tinytag data loggers. Includes a 2-pin connection to logger and 1m flying tails...
General Purpose K-Type Penetration Probe, 100mm x 3.3mm diameter. Supplied with 1 metre PTFE Insulated Lead and a K Therm MiniPlug connector. Probe Temperature Range: -75 to +250°C, Response Time: <5 Seconds. Part Ref 133-158..
5331A3B programmable transmitter with a 7.2-35vDC power supply. Single channel unit for PT100, thermocouple, Resistance or bi-polar mV input, producing a 2-wire 4-20mA output. 1.5kvAC galvanic isolation. Programmed to suit the connected sensor. Transmitter fitted in weatherproof enclosure with 2 cable glands...
This manometer hose set will fit the 9215, 9230 & 9275 series handheld pressure meters. Supplied as 2 x 300 mm lengths x 4mm ID it allows accurate gas pressure testing of heating appliances, flue draught measurement etc...
This manometer hose set will fit the 9205 series handheld pressure meters. Supplied as 2 x 500 mm lengths x 6mm ID it allows accurate gas pressure testing of heating appliances, flue draught measurement etc...
Calibration Certificate for OQ610 Data Logger. OQ610 logger inputs calibrated at 5 points on the T and K type input ranges at 2%, 25%, 50%, 75% and 98% of each range...
SCS Calibration Certificate for MiniAir anemometers, vane anemometers fitted to MiniAir display units and cup anemometers. Price covers a 5 point calibration...
Calibration 2 Axis - Fixed Point (Wind Tunnel). The calibration procedure involves the unit being fixed in one point facing North with a varying wind speed from 0 to 30 or 40m/s. The calibration certificate then compares the wind tunnel velocity readings to those collected by the unit...
Initial Calibration Certificate for Infrared Sensors, PyroMini, PyroCouple and PyroPen. UKAS traceable certificate showing the measured temperature at three points across the sensors temperature range. Only available when ordered along with a brand new sensor...
Licence Key to allow a CMC-99 unit to log data. 1.5GB of internal memory, up to 250 million samples, and a maximum logging speed of 10Hz (limited to a number of recording channels)...
Quick-fit to stainless steel flat base adapter for attachment with epoxy resin. Provides a high rigidity connection but with reduced high frequency response...
Initial Calibration of pressure sensors purchased from Omni Instruments. Pressure Calibration to 5 points. All ranges between -0.8 and 1,000 Bar. Certificate shows actual output readings in graph and table form. Maximum errors shown at each point as a percentage. Certificate is timed, dated and has a unique reference for..
Non-melting hydrocarbon grease. Low contact resistance. 50ml tube. Provides a clear contact from sensor to the surface to improve the ultrasonic signal...
Need help with your products or have a question for us on our custom systems? Use the form below to send us a message and our experts will be in touch to help.
