HYGR201
HygroAir 20 Temperature and Humidity probe with lemo connector for direct connection to the MC20 display. Humidity range 0 to 99.9%RH, accuracy ±1.8% at 10-90%RH. Temperature range -20 to 70°C, accuracy ±0.3°C at 0-40°C...
MPM-393 Connectors
Mating plug mPm-393 with 2m cable...
MULTIDIP
2.4GHZ WiFi antenna centre fed dipole 5m cable SMA..
SCREEN-MODEL-306
Stevenson screen to protect the air temperature probe from the affects of rain and wind on the temperature reading. The white UV stabilized thermoplastic discs offer a high reflectivity, low thermal conductivity and rugged weather resistance. Stainless Steel mounting bracket suitable for pipes up to 27mm, or direct connection to..
UA-KIT-USB-232
SenixView RS-232 Configuration Kit with USB adaptor for sensor setup or real-time monitoring. Kit comes complete with Serial RS-232 to USB converter, serial data cable, Interface board, Universal power supply and software CD (with SenixVIEW software, videos and drivers). Kit is also compatible with Universal Terminal Board and Universal Terminal..
ACS-9701
3 Pin Plug. Suitable for use with all Tinytag Ultra, Plus and View data loggers. For use with the communication interface...
HYGR202
HygroAir 20 Temperature and Humidity probe with 1.8m cable and lemo connector for direct connection to the MC20 display. Humidity range 0 to 99.9%RH, accuracy ±1.8% at 10-90%RH. Temperature range -20 to 70°C, accuracy ±0.3°C at 0-40°C...
UA-KIT-USB-485
SenixView RS-485 Configuration Kit with USB adaptor for sensor setup or real-time monitoring. Kit comes complete with Serial RS-485 to USB converter, Interface board, Universal power supply and software CD (with SenixVIEW software, videos and drivers). Kit is also compatible with Universal Terminal Board and Universal Terminal Board with Relays...
ACS-9703
A 5-pin plug which can be used to connect your own cable for Tinytag voltage and current data loggers. It can also be used to connect your own PT100/PT1000 probe/sensor with suitable Tinytag loggers...
ACS-5050
The Stevenson type screen, or instrument shelter, shield data loggers against precipitation and direct heat radiation from outside sources, while still allowing air to circulate freely around it.This screen is big enough to accommodate two Tinytag Plus 2 sized data loggers...
WIFIBM
2.4GHz Wi-Fi body mounted antenna. Dome shaped, robust waterproof housing...
CAB-3239
Tinytag CAB-3249 Voltage/Current Input Lead for connection of voltage and current input signals to Tinytag data loggers. Includes a 5-pin connection to logger and 1m flying tails...
CAB-3246
Tinytag CAB-3246 Count Input Lead for connection of 2-wire input signals to Tinytag data loggers. Includes a 2-pin connection to logger and 1m flying tails...
133-158
General Purpose K-Type Penetration Probe, 100mm x 3.3mm diameter. Supplied with 1 metre PTFE Insulated Lead and a K Therm MiniPlug connector. Probe Temperature Range: -75 to +250°C, Response Time: <5 Seconds. Part Ref 133-158..
5331A3B-ENCL
5331A3B programmable transmitter with a 7.2-35vDC power supply. Single channel unit for PT100, thermocouple, Resistance or bi-polar mV input, producing a 2-wire 4-20mA output. 1.5kvAC galvanic isolation. Programmed to suit the connected sensor. Transmitter fitted in weatherproof enclosure with 2 cable glands...
551-71
30ml Fill Solution for Polargraphic dissolved Oxygen probe...
825-990
This manometer hose set will fit the 9215, 9230 & 9275 series handheld pressure meters. Supplied as 2 x 300 mm lengths x 4mm ID it allows accurate gas pressure testing of heating appliances, flue draught measurement etc...
825-998
This manometer hose set will fit the 9205 series handheld pressure meters. Supplied as 2 x 500 mm lengths x 6mm ID it allows accurate gas pressure testing of heating appliances, flue draught measurement etc...
890-111
UKAS 3 point Calibration certificate. Only available if purchased at the same time as the meter...
BATT-SB-1/2AA
SAFT LS14250 Size ½AA Battery. Capacity 3.6V @ 1.2Ah...
BATT-SB-C
SAFT LS26500 Size C Battery. Capacity 3.6V @ 7.7Ah...
CAL-SCS-ANEMOMETER
SCS Calibration Certificate for MiniAir anemometers, vane anemometers fitted to MiniAir display units and cup anemometers. Price covers a 5 point calibration...
CAL2AXISFIXEDPOINT
Calibration 2 Axis - Fixed Point (Wind Tunnel). The calibration procedure involves the unit being fixed in one point facing North with a varying wind speed from 0 to 30 or 40m/s. The calibration certificate then compares the wind tunnel velocity readings to those collected by the unit...
CALCERT A
Initial Calibration Certificate for Infrared Sensors, PyroMini, PyroCouple and PyroPen. UKAS traceable certificate showing the measured temperature at three points across the sensors temperature range. Only available when ordered along with a brand new sensor...
