1690-LID-ORGANISER
The 1690 Lid Organiser allows the space in the lid of your 1690 pelicase to be used to store various accessories and tools in small pockets. The organiser can be secured in place with 9 screws into 9 pre-moulded bosses inside the lid...
17124975-1
Replacement MX6 Sensor for Carbon Monoxide (CO). Range 0 to 1,500ppm, Resolution 1.0 ppm. Response Time 10 Seconds (T50)..
17155161
The replacement DualSense pack of Carbon Monoxide sensors for the Tango TX1-1 Gas Detector has a measuring range of 0-1,000 ppm with a 1 ppm resolution. The DualSense pack comes with 2 CO sensors...
380004
FS-1X00 Flame Simulator Replacement/Spare Battery Pack...
400.0108
Bluetooth Output Option for MC 4.0 Handheld Display. Option is only available on new units...
400.0210
Small Transport Case for MC 4.0 Portable Anemometer. Ideal for MC 4.0 Display, probe with cable, Replacement Snapheads and Extra Module. Dimensions: Outside [W x H x D] 238 x 188 x 54mm, Inside 223 x 140 x 41mm...
5331A3B-ENCL
5331A3B programmable transmitter with a 7.2-35vDC power supply. Single channel unit for PT100, thermocouple, Resistance or bi-polar mV input, producing a 2-wire 4-20mA output. 1.5kvAC galvanic isolation. Programmed to suit the connected sensor. Transmitter fitted in weatherproof enclosure with 2 cable glands...
551-71
30ml Fill Solution for Polargraphic dissolved Oxygen probe...
67292
Drycell Batteries for GT Series Gas Detector (Pack of 3). Supplied as standard with all GT instruments..
825-990
This manometer hose set will fit the 9215, 9230 & 9275 series handheld pressure meters. Supplied as 2 x 300 mm lengths x 4mm ID it allows accurate gas pressure testing of heating appliances, flue draught measurement etc...
825-998
This manometer hose set will fit the 9205 series handheld pressure meters. Supplied as 2 x 500 mm lengths x 6mm ID it allows accurate gas pressure testing of heating appliances, flue draught measurement etc...
8816021039
TxConfig Programming USB interface cable and software. Required for programming TxBlock and TxRail transmitters for input range and output. This interface cable is not required for TXBlock-USB and TXRail-USB devices as these will connect via a standard USB cable for configuration...
890-111
UKAS 3 point Calibration certificate. Only available if purchased at the same time as the meter...
98.0030
Aluminium extension rod for the MiniAir/Water range of vane/turbine probes. Diameter 15mm and 180mm long extension rod. Rod includes M12 male and female threads for connecting to all MiniAir, MiniWater and ThermoAir probes...
98.0176
Replacement battery suitable for use with the MiniAir 20 for use in Ex Zones. The MiniAir 20 Ex MUST be fitted with the 9V Daimon E-Block 6LR61, or 9V VARTA 4022, battery for use in any hazardous areas. It is forbidden to change the battery within the Ex-Zone! The battery-connection..
B-530
B-530 Humidity Sensor. Range 0 - 100% RH, output 0 to 1vDC. Suitable for GL Series data loggers. Dimensions 14 mm diameter x 80mm with 3m cable and separate power socket...
BATT-SB-1/2AA
SAFT LS14250 Size ½AA Battery. Capacity 3.6V @ 1.2Ah...
BATT-SB-C
SAFT LS26500 Size C Battery. Capacity 3.6V @ 7.7Ah...
BATT/F1/PB
Replacement Lithium Battery for Fluidwell F1 series Display..
BOT-300
Calibration/Rinse Bottle for the AquaProbes...
CA-11/14
Solsum 6.6F Solar Regulator. This regulator is suitable for solar panel installations with a maximum 146 Watts @ 24vDC (72W @ 12vDC) and a maximum current of 6A. The regulator provides protection to the batteries from over charging and reverse charging during darkness. LED indicators show charging status, operation and..
CAL-610
Calibration Certificate for OQ610 Data Logger. OQ610 logger inputs calibrated at 5 points on the T and K type input ranges at 2%, 25%, 50%, 75% and 98% of each range...
CAL-SCS-ANEMOMETER
SCS Calibration Certificate for MiniAir anemometers, vane anemometers fitted to MiniAir display units and cup anemometers. Price covers a 5 point calibration...
CAL2AXISFIXEDPOINT
Calibration 2 Axis - Fixed Point (Wind Tunnel). The calibration procedure involves the unit being fixed in one point facing North with a varying wind speed from 0 to 30 or 40m/s. The calibration certificate then compares the wind tunnel velocity readings to those collected by the unit...
