AMS84-USB
AMS84-USB All-In-One Measurement System. 16 Amplifier Inputs via AMS-K Cassettes and 5B Amplifiers with 16-Bit Resolution and 250kHz Total Sampling Rate. 2 Analogue Outputs are available via 37-pin Sub-D Connector. 32 Digital Input/Outputs, plus One 32-Bit Counter Input. Power Supply 9-40vDC, (max 20W, depending on number of 5B modules used)...
ANTCFD890EL
Dipole Antenna, 2dBi gain, 5m cable. Suitable for the 868MHz Frequency range...
AP2A
Mounting backplane for up to 2 5B series amplifiers. Power supply 9-40vDC or +5vDC ( max 1.5 amps )...
AP8A
Mounting backplane for up to 8 5B series amplifiers. Power supply 9-40vDC or +5vDC ( max 1.5 amps )...
0362611
Waterproof 4-pin plug connector with 10m of pre-wired high quality yellow signal cable with 4 wires and a shield covered with black sleeve. Suitable for the following Kipp & Zonen equipment. CMP Series pyranometers, CGR3 & CGR4 pyrgeometers and CVF4 & CNF4 ventilation units...
GS-3AT
GS-3AT Acceleration and temperature sensor. Acceleration, in 3-axes, range max 10g. Temperature -10 to 50°C. The sensor can provide Peak (largest value each interval), average (mean value during interval) and RMS (root mean square value) acceleration readings at set sampling rates of 500ms up to 60 mins (Sub-sampling interval is..
OceanDISP-1K
OceanDISP-1K subsea LED display unit suitable for displaying sensor readings from Datataker DT80 and DT85 data loggers. Light activated scrolling display with programmable scroll interval. Suitable for depths up to 1,000m..
0362613
Waterproof 4-pin plug connector with 25m of pre-wired high quality yellow signal cable with 4 wires and a shield covered with black sleeve. Suitable for the following Kipp & Zonen equipment. CMP Series pyranometers, CGR3 & CGR4 pyrgeometers and CVF4 & CNF4 ventilation units...
0362614
Waterproof 4-pin plug connector with 50m of pre-wired high quality yellow signal cable with 4 wires and a shield covered with black sleeve. Suitable for the following Kipp & Zonen equipment. CMP Series pyranometers, CGR3 & CGR4 pyrgeometers and CVF4 & CNF4 ventilation units...
APS-SERIES-AP
APS Series Autopilot Platform :size (2.63 inch W x 2.10 inch H x 2.63 inch D) , 30 fully programmable digital I/O lines , 4 RS-232, full duplex UARTS , PWM inputs and outputs for servo control , 12 Analog inputs (12 bit) , 5 VDC supply for analog, Hall-effect,..
APS21024
Microbot APS Development Kit complete with autopliot programming dongle, second ( ground station radio modem ) and antennas...
APSN
Air purge collar for PyroMini -151, -201, -301 and CF models. The air purge collar is used to keep dust, fumes, moisture, and other contaminants away from the lens. It must be screwed fully onto the sensing head. Air flows into the 1/8 BSP fitting and out of the front..
APSW
Air purge collar for PyroMini -21 models. The air purge collar is used to keep dust, fumes, moisture, and other contaminants away from the lens. It must be screwed fully onto the sensing head. Air flows into the 1/8 BSP fitting and out of the front aperture. Air flow should..
2523146
Waterproof 8-pin plug connector for the following Kipp & Zonen equipment. SMP Pyranometers, SGR Pyrgeometers, SUV Radiometers, CMP Pyranometers with PT100 output, CGR3 and CGR4 with PT100 output, CHP1, CNR4, UVS Radiometers and CSD3 Sunshine Duration Sensors...
GS-LXUV
GS-LXUV Illuminance and Ultra Violet intensity measurement. Illuminance Range: 0 to 200 kLux, UV intensity Range: 0 to 30mW/cm² with a 1ms response time. Also allows for the calculation of accumulated Illuminance and UV intensity. Accumulated illuminance 0 to 99,999kLuxh. 16 Byte record length, 111 days logging to internal memory..
B-568
Wireless LAN Adapter for GL260 & 860 Series Data Loggers. The B-568 WLAN option enables wireless communication with various devices. The adapter allows the Data Logger GL260 or GL860 to be used as an access point for the GL100-WL to use. If the GL260 or GL860 configured as station, PC..
B103479
Alignment kit for Safeye detectors. (includes telescope, test filter and case)..
B103829
Wall mounted uninterrupted 24vDC power supply backup-system for MX15 & MX32 controllers. Dimensions 322 x 248 x 126 mm. Batteries capacity 7Ah...
B103875
40/40I Triple IR (IR3) SharpEye Flame Detector. Detector suitable for near detection with a sensitivity range of 30m for a 0.1m gasoline fire and Built In Test. The unit is fitted with a tilt mount and one swivel mount, ATEX sealing plug and M25 x 1.5 mm cable entries (cable..
B103876
40/40I Triple IR (IR3) SharpEye Flame Detector. Detector suitable for far detection with a sensitivity range of 65m for a 0.1m gasoline fire and Built In Test. The unit is fitted with a tilt mount and one swivel mount, ATEX sealing plug and M25 x 1.5 mm cable entries (cable..
B103879
40/40M Multi IR (IR4) SharpEye Flame Detector. Detector suitable for near detection with a sensitivity range of 30m for a 0.1m gasoline fire and Built In Test. The unit is fitted with a tilt mount and one swivel mount, ATEX sealing plug and M25 x 1.5 mm cable entries (cable..
B103880
40/40M Multi IR (IR4) SharpEye Flame Detector. Detector suitable for far detection with a sensitivity range of 65m for a 0.1m gasoline fire and Built In Test. The unit is fitted with a tilt mount and one swivel mount, ATEX sealing plug and M25 x 1.5 mm cable entries (cable..
B103883
40/40LB UV/IR SharpEye Flame Detector. Detector suitable for very near detection with a sensitivity range of 15m for a 0.1m gasoline fire and Built In Test. The unit is fitted with a tilt mount and one swivel mount, ATEX sealing plug and M25 x 1.5 mm cable entries (cable gland..
B103884
40/40L UV/IR SharpEye Flame Detector. Detector suitable for very near detection with a sensitivity range of 15m for a 0.1m gasoline fire and without Built In Test. The unit is fitted with a tilt mount and one swivel mount, ATEX sealing plug and M25 x 1.5 mm cable entries (cable..
